4/17/2023 0 Comments Overdrive cpu stress test![]() At some point, there will be a limit imposed by the ability to supply the device with sufficient power, the user's ability to cool the part, and the device's own maximum voltage tolerance before it achieves destructive failure. While in a PC context the usual result is a system crash, more subtle errors can go undetected, which over a long enough time can give unpleasant surprises such as data corruption (incorrectly calculated results, or worse writing to storage incorrectly) or the system failing only during certain specific tasks (general usage such as internet browsing and word processing appear fine, but any application wanting advanced graphics crashes the system).Īt this point, an increase in operating voltage of a part may allow more headroom for further increases in clock speed, but the increased voltage can also significantly increase heat output, as well as shorten the lifespan further. Past this speed, the device starts giving incorrect results, which can cause malfunctions and sporadic behavior in any system depending on it. Generally for any given voltage most parts will have a maximum "stable" speed where they still operate correctly. While most modern devices are fairly tolerant of overclocking, all devices have finite limits. Also base operating voltage may be increased to compensate for unexpected voltage drops and to strengthen signalling and timing signals, as low-voltage excursions are more likely to cause malfunctions at higher operating speeds. Examples are that operating temperature would need to be more strictly controlled with increased cooling, as the part will be less tolerant of increased temperatures at the higher speeds. Overclocking techniques in general aim to trade this safety margin by setting the device to run in the higher end of the margin, with the understanding that temperature and voltage must be more strictly monitored and controlled by the user. Most components are designed with a margin of safety to deal with operating conditions outside of a manufacturer's control examples are ambient temperature and fluctuations in operating voltage. The trade-offs are an increase in power consumption (heat), fan noise (cooling), and shortened lifespan for the targeted components. Normally, on modern systems, the target of overclocking is increasing the performance of a major chip or subsystem, such as the main processor or graphics controller, but other components, such as system memory ( RAM) or system buses (generally on the motherboard), are commonly involved. ![]() The purpose of overclocking is to increase the operating speed of a given component. 12.1 Overclocking and benchmark databases.2.2 Stability and functional correctness.Many device warranties state that overclocking or over-specification voids any warranty, however there are an increasing number of manufacturers that will allow overclocking as long as performed (relatively) safely. An overclocked device may be unreliable or fail completely if the additional heat load is not removed or power delivery components cannot meet increased power demands. Semiconductor devices operated at higher frequencies and voltages increase power consumption and heat. Commonly, operating voltage is also increased to maintain a component's operational stability at accelerated speeds. In computing, overclocking is the practice of increasing the clock rate of a computer to exceed that certified by the manufacturer. This corresponds to an overclocking of the FSB by 11.3% and of the CPU by 36%. Front side bus (FSB) frequency (external clock) has been increased from 133 MHz to 148 MHz, and the CPU clock multiplier factor has been changed from 13.5 to 16.5. Make sure your temps don't go above 80C degrees when stress testing.Overclocking BIOS setup on an ABIT NF7-S motherboard with an AMD Athlon XP processor. The best overclock is going to be a combination of messing with all three settings. Then back it down by 1 multiplier and attempt to run Prime95 for 8 hours without any errors or crash. If the system doesn't crash, increase the multiplier by 1 again. Monitor CPU voltage with CPU-Z or HWMonitor. If you are using the stock CPU cooler, figure out what the default voltage is, and put that value in for CPU voltage in BIOS. Start by just increasing the multiplier by 1 from its default value. Then it would just be figuring out how much voltage is needed to keep it stable. So if you wanted 4.0GHz, you could do 20 for the multiplier and 200 for the bus speed. The CPU multiplier times the CPU bus speed gives you the MHz the CPU will run at. The CPU multiplier, CPU bus speed and CPU voltage are all you have to mess with. Why not just do it through BIOS? Go into BIOS and go to the Overclock Tweaker.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |